Problems running DOS software under Windows XP. Occasional problems with DOS software running under Windows XP. Well folks Windows XP (and 2. NT) has a wonderful new feature. Occasionally it just decides that it no longer wants to run DOS software like the software posted on this site. So it doesn't. Our job is to convince Windows XP that we would really appreciate it if it would once again run DOS software. The following information is from the Microsoft site. Windows; Run DOS programs in Windows 7. Comments. By Lincoln Spector, PCWorld. Nov 28, 2011 7:53 AM. Here's the general rule: If the DOS program ran in. Describes how to troubleshoot MS-DOS-based programs in Windows XP. Troubleshooting MS-DOS-based. to make sure that the program is supported under Windows. Unfortunatly this requires that you mess with the system files on your computer because Windows XP has screwed them up. Be extremely careful following these instructions. SYMPTOMSIf you try to start or install an MS- DOS- based or a 1. Windows- based program on your Windows XP- based computer, you may receive an error message that is similar to one of the following: 1. MS- DOS Subsystem path to the program that you are trying to start or install C: \Winnt\System. The system file is not suitable for running MS- DOS and Microsoft Windows applications. Choose 'Close' to terminate the application. MS- DOS Subsystem path to the program that you are trying to start or install config. The system file is not suitable for running MS- DOS and Microsoft Windows applications. Choose 'Close' to terminate the application. MS- DOS Subsystem path to the program that you are trying to start or install. C: \Windows\System. Autoexec. nt. The system file is not suitable for running MS- DOS and Microsoft Windows applications. Choose 'Close' to terminate the application. Although you may be prompted to quit the program or ignore the error message, either selection makes the program quit. This issue may occur if one or more of the following files are missing or damaged. Config. nt. Autoexec. Windows XP Mode'da bir program yüklerseniz, bu program hem Windows XP Mode'un programlar listesinde, hem de Windows 7 programlar listesinde görünür. Windows Programs Not Designed for XP. The three main reasons older Windows programs fail under Windows XP are that they query for a specific Windows version number. Command. com. NOTE: It has been suggested (with success) that you only do instructions 7 - 1. If you do stop at instruction 1. In the followng instructions I assume that by "CD" Microsoft means the CD with Windows XP (or 2. . Window under XP. The application is a FoxPro for DOS. Running DOS Application under Windows 7. program. It runs perfectly in 32 bit Windows 7.NT) on it. RESOLUTIONTo resolve this issue. Insert the CD into the CD drive or DVD drive. Click Start, and then click Run. In the Open box, type cmd, and then click OK. At the command prompt, type the following commands, pressing ENTER after each command: expand CD- ROM Drive Letter: \i. CD- ROM Drive Letter: \i. CD- ROM Drive Letter: \i. Start or install the program. If the issue is resolved, do not complete the remaining steps. If the issue is not resolved, go to the next step. Note: The Command. Because of this, you may have to expand it from your Windows XP CD- ROM. Start Notepad. 7. In Notepad, type the following entries: dos=high, umb. SYSTEMROOT%\system. On the File menu, click Save As. In the File Name box, type Config. Save. Close the Config. On the File menu, click New. In the new blank document, type the following entries: @echo off. SYSTEMROOT%\system. SYSTEMROOT%\system. SYSTEMROOT%\system. SET BLASTER=A2. 20 I5 D1 P3. T3. 1. 2. On the File menu, click Save As. In the File Name box, type Autoexec. Save. Close the Autoexec. Start Windows Explorer. Locate the Config. Config. nt file, and then click Copy. Right- click the %SYSTEMROOT%\System. Paste. 1. 6. Locate the Autoexec. Autoexec. nt file, and then click Copy. Right- click the %SYSTEMROOT%\System. Paste. 1. 8. Locate the Command. Command. com file, and then click Copy. Right- click the %SYSTEMROOT%\System. Paste. Restart your computer. Press [BACK] on your browser to return to the main page, or. Run DOS programs in Windows 7. Robert Wray wants to know if his old DOS programs will run in Windows 7. Here's the general rule: If the DOS program ran in XP, it will probably run in a 3. Windows 7. But no DOS program can ever run in a 6. Windows 7. Except that there's a workaround. I'll explain it in a minute. If you're not sure whether your Windows is 3. Start orb, right- click Computer, and select Properties. Look for the System type. You can launch most DOS apps in a 3. Windows 7 simply by double- clicking the DOS program's . If it doesn't work, or if there are problems, right- click the file and select Properties. Click the Compatibility tab. Check the "Run this program in compatibility mode for" option and select an older version of Windows. You may have to do some experimenting to find the right one. And if none of those work, try the 6. Actually, there are several solutions, all of which involve using software to create a virtual machine (VM) inside Windows. If you want to run a lot of different operating systems inside Windows, VMware Player is probably your best bet. But if all you're only looking for is a way to run DOS programs, try DOSBox, a free program that launches a DOS VM. I can't promise it will work with every program you throw at it, but it worked for every one I tried. Once you download and install DOSBox, here's how to set it up so that it can find and work with your DOS programs and files: Create a folder (just as an example, let's call it C: \DOSFiles) and place in it every program and file you want DOSBox to access. You can use subfolders within that folder. Click Start, type notepad and press ENTER to bring up Notepad. Click Start, and select All Programs, DOSBox- 0. Extras, Screenshots & Recordings. This will open Windows Explorer to a probably empty folder inside the DOSBox configuration folder. In the path bar at the top of the window, click DOSBox to go to that folder. Drag the file dosbox- 0. Notepad. (The . conf part will probably not be visible.)In Notepad, go to the bottom of the file, where you'll find the [autoexec] section. On a blank line at the end of the file, type mount driveletterpath, where driveletter is the drive letter you wish to assign the folder to, and path is the path to that folder. For instance, mount a c: \dosfiles wil make the C: \DOSFiles folder appear as DOSBox's drive A. Save the file and launch DOSBox. Contributing Editor Lincoln Spector writes about technology and cinema. Email your tech questions to him at answer@pcworld. PCW Answer Line forum. Follow Lincoln on Twitter, or subscribe to the Answer Line newsletter, e- mailed weekly. Ericuse. 16. 5 has a friend with a PC that's making a grinding noise. Eric asked the Hard Drives, NAS Drives, Storage forum for advice.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. Archives
September 2016
Categories |